Iron & Metal Fence Cost Calculator — Texas

Average iron & metal fence cost in Texas: $14,139 (typical range $12,442–$16,260, $94 per linear foot). Enter your own sizes below for an itemized estimate. Updated November 2026

Loading calculator…

Free · No obligation

Get up to 3 free quotes from Texas pros

  • Compare real prices with your estimate
  • Local, licensed and insured contractors
  • Takes 30 seconds — your estimate is attached

How much does a iron & metal fence cost in Texas?

Based on current Texas labor rates and material prices, a typical iron & metal fence costs about $14,139. Most projects fall between $12,442 and $16,260, or roughly $94 per linear foot. This example assumes: type Wrought iron / ornamental steel, length 150 ft, height 5 ft, gates 1 walk / 0 drive.

Cost by project size

Project sizeEstimated cost
75 ft$8,026
150 ft$14,139
300 ft$26,870

Where the money goes

  • Fence materials$9,829 (91%)
  • Gates & automation$611 (6%)
  • Permit & layout$308 (3%)

Materials $8,680 · Labor $1,940 (48 hours) · Equipment, disposal & permits $128 — before contingency, contractor overhead & profit and tax.

Texas vs. United States average

A typical iron & metal fence in Texas costs 5% less than the United States average ($14,139 vs. $14,917). The difference comes mainly from local wages — a carpenter earns on average $24.51 per hour in Texas — and from regional material prices and Sales tax (materials) of 6.25%.

Iron & Metal Fence in Texas: local factors

Texas ranks 44th of 51 states for iron & metal fence cost (1 = most expensive) — among the most affordable.

Nearby stateTypical costvs. Texas
Texas$14,139—
Arkansas$13,670-3%
Louisiana$14,134-0%
New Mexico$14,276+1%
Oklahoma$13,848-2%

What affects the price in Texas

  • Hurricane-force winds: Fences must resist high winds: deeper concrete-set posts, closer post spacing or reinforced masonry.

Permits & contractor licensing in Texas

  • Contractor license: Texas has no statewide license for general or remodeling contractors. Plumbers are licensed by the Texas State Board of Plumbing Examiners, and electricians and HVAC contractors by the Texas Department of Licensing and Regulation (TDLR).
  • Building code: Cities enforce the International Residential Code (the edition varies by city). Unincorporated county areas have few building rules, so check what applies at your address.
  • Permits: Permits are issued by the city. In the 14 coastal counties, windstorm certification from the Texas Department of Insurance is needed to keep TWIA wind coverage.

Verify a contractor: Texas Department of Licensing and Regulation (TDLR) ↗. Rules change — always confirm with your local building department.

Labor rates for this project in Texas

TradeHoursAvg. wage / hourInstalled rate / hour
Fence erector48$20.04$40.08
  • Labor wages: U.S. Bureau of Labor Statistics (BLS), Occupational Employment and Wage Statistics — state hourly mean wage by trade — data period May 2025, last checked November 21, 2026.
  • Material price index: U.S. BLS Producer Price Index — inputs to construction industries (WPUSI012011), monthly — data period October 2026, last checked November 21, 2026.

What a iron & metal fence includes

Metal fences range from budget chain link to ornamental aluminum and wrought iron. Driveway gates and automatic openers can cost as much as the fence itself.

Main cost factors

  • Fence type
  • Length and height
  • Walk and driveway gates
  • Automatic gate opener
  • Finish (galvanized, powder coat)

How to save money

  • Chain link is the cheapest way to enclose a large yard.
  • Aluminum looks like iron but never rusts and costs less.
  • Powder-coated steel lasts much longer than painted steel.
  • Sliding gates suit sloped driveways; swing gates are cheaper on flat ground.

Timeline

2–5 days, plus 2–4 weeks for custom gates.

Permits

Permits are often required for fences over 6 ft and for electrical work on gate openers.

Frequently asked questions

How much does a iron & metal fence cost in Texas?

A typical iron & metal fence in Texas costs about $14,139, with most projects between $12,442 and $16,260. That is about $94 per linear foot.

How much of the cost is labor?

Labor is about 18% of the direct cost (48 work hours) for a typical project in Texas. Materials are $8,680 and equipment, disposal and permits $128, before contingency, contractor overhead and tax.

Is a iron & metal fence cheaper in Texas than in nearby states?

A typical iron & metal fence costs $14,139 in Texas. Among nearby states, Arkansas is the lowest at $13,670 and New Mexico the highest at $14,276. Differences come mostly from local wages, material prices and taxes.

Do I need a licensed contractor in Texas?

Texas has no statewide license for general or remodeling contractors. Plumbers are licensed by the Texas State Board of Plumbing Examiners, and electricians and HVAC contractors by the Texas Department of Licensing and Regulation (TDLR).

What local conditions affect iron & metal fence costs in Texas?

Fences must resist high winds: deeper concrete-set posts, closer post spacing or reinforced masonry.

How long does a iron & metal fence take?

2–5 days, plus 2–4 weeks for custom gates.

Do I need a permit for a iron & metal fence?

Permits are often required for fences over 6 ft and for electrical work on gate openers.

Is wrought iron more expensive than aluminum?

Yes — compare both by switching the fence type above.

How much does an automatic gate opener cost?

Turn on “Automatic gate opener” to see opener, safety and wiring costs.

Can I change the contractor markup or contingency?

Yes — open “Contingency & contractor markup” in the calculator. Set overhead & profit to 0% if you manage the project yourself and hire trades directly.

Iron & Metal Fence cost in other states

Compare iron & metal fence costs in every state, province and territory →

More cost calculators for Texas

Choose your location

AL AlabamaAK AlaskaAZ ArizonaAR ArkansasCA CaliforniaCO ColoradoCT ConnecticutDE DelawareDC District of ColumbiaFL FloridaGA GeorgiaHI HawaiiID IdahoIL IllinoisIN IndianaIA IowaKS KansasKY KentuckyLA LouisianaME MaineMD MarylandMA MassachusettsMI MichiganMN MinnesotaMS MississippiMO MissouriMT MontanaNE NebraskaNV NevadaNH New HampshireNJ New JerseyNM New MexicoNY New YorkNC North CarolinaND North DakotaOH OhioOK OklahomaOR OregonPA PennsylvaniaRI Rhode IslandSC South CarolinaSD South DakotaTN TennesseeTX TexasUT UtahVT VermontVA VirginiaWA WashingtonWV West VirginiaWI WisconsinWY Wyoming