Paver Patio Cost Calculator — North Carolina

Average paver patio cost in North Carolina: $5,758 (typical range $5,067–$6,622, $19 per sq ft). Enter your own sizes below for an itemized estimate. Updated November 2026

Loading calculator…

Free · No obligation

Get up to 3 free quotes from North Carolina pros

  • Compare real prices with your estimate
  • Local, licensed and insured contractors
  • Takes 30 seconds — your estimate is attached

How much does a paver patio cost in North Carolina?

Based on current North Carolina labor rates and material prices, a typical paver patio costs about $5,758. Most projects fall between $5,067 and $6,622, or roughly $19 per sq ft. This example assumes: patio area 300 sq ft, paver Concrete pavers, base 6".

Cost by project size

Project sizeEstimated cost
150 sq ft$3,268
300 sq ft$5,758
600 sq ft$11,162

Where the money goes

  • Pavers$2,481 (56%)
  • Excavation$1,052 (24%)
  • Base$934 (21%)

Materials $2,243 · Labor $1,315 (41 hours) · Equipment, disposal & permits $910 — before contingency, contractor overhead & profit and tax.

North Carolina vs. United States average

A typical paver patio in North Carolina costs 9% less than the United States average ($5,758 vs. $6,312). The difference comes mainly from local wages — a carpenter earns on average $24.28 per hour in North Carolina — and from regional material prices and Sales tax (materials) of 4.75%.

Paver Patio in North Carolina: local factors

North Carolina ranks 47th of 51 states for paver patio cost (1 = most expensive) — among the most affordable.

Nearby stateTypical costvs. North Carolina
North Carolina$5,758—
Georgia$5,818+1%
South Carolina$5,856+2%
Tennessee$5,884+2%
Virginia$6,052+5%

Permits & contractor licensing in North Carolina

  • Contractor license: Projects of $40,000 or more require a license from the NC Licensing Board for General Contractors; electrical, plumbing and HVAC work need separate state licenses.
  • Building code: The North Carolina Residential Code applies statewide, enforced by county and city inspection departments.
  • Permits: Permits are issued by the county or city inspections department; homeowners may pull permits for work on their own home.

Verify a contractor: NC Licensing Board for General Contractors ↗. Rules change — always confirm with your local building department.

Labor rates for this project in North Carolina

TradeHoursAvg. wage / hourInstalled rate / hour
Landscaper / hardscape41$16.24$32.48
  • Labor wages: U.S. Bureau of Labor Statistics (BLS), Occupational Employment and Wage Statistics — state hourly mean wage by trade — data period May 2025, last checked November 21, 2026.
  • Material price index: U.S. BLS Producer Price Index — inputs to construction industries (WPUSI012011), monthly — data period October 2026, last checked November 21, 2026.

What a paver patio includes

A paver patio is mostly excavation and base work: geotextile, crushed gravel, bedding sand, then the pavers, edge restraint and polymeric joint sand. A good base is what keeps pavers level for decades.

Main cost factors

  • Patio area
  • Paver type
  • Base depth
  • Borders and edging
  • Steps or seat walls

How to save money

  • Do not skimp on base depth on clay soils.
  • Simple running-bond patterns waste less paver material.
  • Permeable pavers can reduce storm-water fees in some cities.
  • Seat walls and steps add the most cost per square foot.

Timeline

2–5 days.

Permits

Usually not required for ground-level patios; check lot coverage rules.

Frequently asked questions

How much does a paver patio cost in North Carolina?

A typical paver patio in North Carolina costs about $5,758, with most projects between $5,067 and $6,622. That is about $19 per sq ft.

How much of the cost is labor?

Labor is about 29% of the direct cost (41 work hours) for a typical project in North Carolina. Materials are $2,243 and equipment, disposal and permits $910, before contingency, contractor overhead and tax.

Is a paver patio cheaper in North Carolina than in nearby states?

A typical paver patio costs $5,758 in North Carolina. Among nearby states, Georgia is the lowest at $5,818 and Virginia the highest at $6,052. Differences come mostly from local wages, material prices and taxes.

Do I need a licensed contractor in North Carolina?

Projects of $40,000 or more require a license from the NC Licensing Board for General Contractors; electrical, plumbing and HVAC work need separate state licenses.

How long does a paver patio take?

2–5 days.

Do I need a permit for a paver patio?

Usually not required for ground-level patios; check lot coverage rules.

How much base gravel do I need?

See the “Base” category for cubic yards for your base depth.

How long do paver patios last?

25–50 years with occasional re-sanding of joints.

Can I change the contractor markup or contingency?

Yes — open “Contingency & contractor markup” in the calculator. Set overhead & profit to 0% if you manage the project yourself and hire trades directly.

Paver Patio cost in other states

Compare paver patio costs in every state, province and territory →

More cost calculators for North Carolina

Choose your location

AL AlabamaAK AlaskaAZ ArizonaAR ArkansasCA CaliforniaCO ColoradoCT ConnecticutDE DelawareDC District of ColumbiaFL FloridaGA GeorgiaHI HawaiiID IdahoIL IllinoisIN IndianaIA IowaKS KansasKY KentuckyLA LouisianaME MaineMD MarylandMA MassachusettsMI MichiganMN MinnesotaMS MississippiMO MissouriMT MontanaNE NebraskaNV NevadaNH New HampshireNJ New JerseyNM New MexicoNY New YorkNC North CarolinaND North DakotaOH OhioOK OklahomaOR OregonPA PennsylvaniaRI Rhode IslandSC South CarolinaSD South DakotaTN TennesseeTX TexasUT UtahVT VermontVA VirginiaWA WashingtonWV West VirginiaWI WisconsinWY Wyoming